Euro Spec Lights

32980 Views 90 Replies 30 Participants Last post by mingo, 2 mo ago

dinoone

Discussion Starter · Jan 3, 2019

3

If you are on the fence about doing this it's a must. Changes the entire look of the bike. Here is a side by side Pic of my two monkeys. I've ordered another set up for my Yellow bike.

Sent from my iPhone using Tapatalk Pro

See less See more

Reactions: 2

61 - 80 of 91 Posts

Swampass

· #61 · Mar 12, 2019

If your kit is the same as mine, the screws and nutsert style clips are listed in previous posts. (all US kits purchased seem to have the same stuff in them) You will need two additional screws to affix the rear signals to their base. I got those form a hardware store. You will need the relay from Steady Garage. Our signal relay isn't like the one provided. It's three prongs in line vs. the relay sent in the kit.

Kacz

· #62 · Mar 12, 2019 (Edited)

Another option from MNNTHBX to work all the LEDs:

https://mnnthbx.com/product/custom-led-electronic-flasher-for-honda-monkey/

Aside from that as other stated you are basically going to need bolts for all the signals (mine came with 1 of 4?) and the list of stuff from earlier in the post.

Follow the parts diagram posted earlier - assume you get no hardware (as everyone seems to be getting something a little different) and order it all when you order the kit, then you will have everything you need once delivered.

Suga Sean

· #63 · Mar 13, 2019 (Edited)

Appreciate all the help guys. Seems as if we have some of the screws already on the bike now. I will order the additional parts today.
Heres what I am ordering of it can help anyone else who may purchase from hrp.

90115-KW7-900 (3x)
90302-KWW-A00 (2x)
90677-KAN-T00 (3x)
93903-34410 (3x)
The 33462-K0f-T01 and the 93411-0501600 (2x) were not availble through honda usa.

Swapass, Did all the turn signal wire have to be extended?

Swampass

· #64 · Mar 13, 2019

yes. I took the wire ends from the US OEM set up and crimped wire to wire connectors on them. Then I used heat shrink wrap. The OEM brake/tail light connecter fits the Japanese tail light and works without any changes.

Reactions: 1

Swampass

· #65 · Mar 13, 2019

double check the relay you get from Steady Garage if you order one. They have an adapter that goes with it. Both blades of the adapter I received were bent. I saw them before I went to install it. Also, the blades push out of the adapter very easily. I secured them with a crap ton of electrical tape. I couldn't get the relay to fit where the factory one went so I zip tied it to the loom on the left side of the bike.

Reactions: 1

Suga Sean

· #66 · Mar 13, 2019

The bolts for the rear blinkers if anyone is looking for the correct size

See less See more

Kacz

· #67 · Mar 13, 2019 (Edited)

the bolts for the rear blinkers according to the diagram are only 5x16. 5x20 might fit if the cavity is deep enough, but might bottom out.

The Honda part number is 93411-0501600. When I ordered my parts this part wasn't available (from partzilla) so I found and ordered 93401-0501608 in place of it and worked like a charm.

Here was my final part requirement:

93401-0501608 (x2) - two 5x16 bolts for rear blinkers
90115-KW7-900 (x3) - screw for attaching light to assembly
90302-KWW-A00 (x2) - 4mm spring nut to attach assembly to stay
93903-34410 (x5) - twp for assembly to stay, three for LED brake to back housing cover
90677-KAN-T00 (x3) - 5mm spring nut for housing to stay
93411-05025-00 (x2) - two 5x25 bolts for front blinkers

plus the flasher with harness from MNNTHBX I linked above to make it all work.

See less See more

Suga Sean

· #68 · Mar 13, 2019

Fawk I didn't see the other two screw listed and Dino said the same thing. Guess back on the phone I go tomorrow....... Damn it. The 5x20 didn't fit either. So back to the hardware store F.M.

Suga Sean

· #69 · Mar 14, 2019

Too long yet again :yawn:

See less See more

Kacz

· #70 · Mar 14, 2019 (Edited)

yeah don't think there is room for much more than a 16 on there. And they aren't as common state side. You could:

1. find a 5x16
2. find a 5x15 which would be a little more common and fit fine and should hold well (+blue loctite)
3. cut 1/4 of the length of your 5x20 off (5mm) but would prob mangle threads and be more trouble than worth
4. 4mm stack of 5mm washers on your 5x20
5. order any honda 5x16 from Honda and wait

Good luck

Reactions: 1

Suga Sean

· #71 · Apr 16, 2019

I misplaced the extra parts needed to complete the install. So I ordered another set. Well low and behold found the missing set. So if anyone needs the extra parts I have a set.

Reactions: 1

mumdb1

· #72 · Apr 17, 2019

Suga Sean said:
I misplaced the extra parts needed to complete the install. So I ordered another set. Well low and behold found the missing set. So if anyone needs the extra parts I have a set.

Sent you a PM!

Reactions: 1

PacificoFlyr

· #73 · Jun 15, 2019

Kacz said:
the bolts for the rear blinkers according to the diagram are only 5x16. 5x20 might fit if the cavity is deep enough, but might bottom out.

The Honda part number is 93411-0501600. When I ordered my parts this part wasn't available (from partzilla) so I found and ordered 93401-0501608 in place of it and worked like a charm.

Here was my final part requirement:

93401-0501608 (x2) - two 5x16 bolts for rear blinkers
90115-KW7-900 (x3) - screw for attaching light to assembly
90302-KWW-A00 (x2) - 4mm spring nut to attach assembly to stay
93903-34410 (x5) - twp for assembly to stay, three for LED brake to back housing cover
90677-KAN-T00 (x3) - 5mm spring nut for housing to stay
93411-05025-00 (x2) - two 5x25 bolts for front blinkers

plus the flasher with harness from MNNTHBX I linked above to make it all work.

Awesome thank you guys! Was anything else needed for the install?

KBK0

· #74 · Jun 23, 2019 (Edited)

https://www.bike-parts.fr/honda-mot...Z125MAK/Chassis/CLIGNOTANT/98345/F_35/2/36588

https://www.bike-parts.fr/honda-mot...125MAK/Chassis/FEU-ARRIERE/98345/F_36/2/36588

Vehicle Motor vehicle Car Motorcycle Automotive design

See less See more

KBK0

· #75 · Jun 28, 2019

3

See less See more

Reactions: 2

PacificoFlyr

· #76 · Jul 2, 2019

Awesome great pics. Mine is arriving shortly and I can't wait to put it on.

PacificoFlyr

· #77 · Jul 22, 2019

2

Stoked on the new lights, also did the rack at the same time. Mine did come with a flasher relay but order all of that hardware from the list above. Thanks for making that list and making the install predictable!

See less See more

Reactions: 1

GdubluG

· #78 · Aug 16, 2019

Hs anyone found a good source for the bullet pin connectors? I cannot find any small enough locally

Madgrommer

· #79 · Aug 26, 2019

Hey guys I actually looped my monkey today and need a new tailigut and top cover piece. Together these parts are freaking 200$!?!! From bike bandit. What is the cheapest way into the euro rear light setup? Hrp wants 455$ for front, rears, and flasher relay insane. There are some eBay listings but they do not specify if they come with turn signals or not. So where's the cheapest place to get this stuff?

Vrmmmpshhh

· #80 · Aug 26, 2019 (Edited)

GdubluG said:
Hs anyone found a good source for the bullet pin connectors? I cannot find any small enough locally

I pulled some from a alpine car stereo harness.

I have a spare grom light I was gonna to cut for the plug but Honda were sneaky bastards and reversed the harness on the monkey so they are both male plugs!!!

Sent from my iPhone using Tapatalk

61 - 80 of 91 Posts